35W DALI2 & PUSH dimming constant current driver NFC programmable LED driver 500-1050mA
【Product Feature】
- Flicker-free for the whole dimming range
- Stand-by power below 0.5W
- Primary dimming with a push button
- NFC technology for wireless programming
- Built-in DALI interface DT6
- Centrally-supplied DC emergency operation DT19
- CLO compensation
- Protection: short circuit / over temperature/ over voltage
- Derating the current for a high ambient temperature
- Push dim with memory function
- 5-year warranty
【Parameters】
| | Micro series | KL10C-PDiiN | KL20C-PDiiN | KL35C-PDiiN |
| Input | Operating Voltage | 198-264Vac 50Hz/60Hz |
| Rated Input Voltage | 220-240Vac 50Hz/60Hz |
| DC Input Voltage range | 200-240Vdc |
| Input Current | 0.06A Max. | 0.11A Max. | 0.19A Max. |
| Input Inrush Current | <15A (Half current pulse width100μs) @230Vac |
| Power factor(@230V100% load) | ≥ 0.9C | ≥ 0.93 | ≥ 0.95 |
| Total harmonic distortion | Typical:15% (@230Vac, 100% load) |
| Stand-by power | ≤0.5W (@230Vac when PUSH or DALI turn off) |
| Efficiency(@230Vac,100% load) | 81% | 86% | 87% |
| Wiring Method | 0.75mm2 | 0.75-1.5mm2 |
| Automatic circuit breaker | KL10C-PDiiN (Calculate current in the wire) |
| type | B10 | B13 | B16 | B20 | B25 | / |
| Number | 40 | 50 | 65 | 85 | 100 | / |
| type | C10 | C13 | C16 | C20 | C25 | C32 |
| Number | 70 | 90 | 110 | 140 | 170 | 220 |
| KL20C-PDiiN (Calculate current in the wire) |
| type | B10 | B13 | B16 | B20 | B25 | / |
| Number | 25 | 35 | 45 | 55 | 65 | / |
| type | C10 | C13 | C16 | C20 | C25 | C32 |
| Number | 60 | 70 | 80 | 110 | 130 | 160 |
| KL35C-PDiiN (Calculate current in the wire) |
| type | B10 | B13 | B16 | B20 | B25 | / |
| Number | 25 | 30 | 40 | 50 | 60 | / |
| type | C10 | C13 | C16 | C20 | C25 | C32 |
| Number | 40 | 55 | 60 | 80 | 105 | 130 |
| Output | Operating mode | Constant Current |
| Load type | LED |
| Ripple requirement (Flickering or Flickering-Free) | Flicker value: less than 5% for the whole dimming range |
| Start up time | <1s (@230Vac) |
| No-load output voltage | 50V DC Max. | 55V DC Max. | 55V DC Max. |
| Load output voltage range | 3-40V DC | 12-40V DC | 12-40V DC |
| Full load output power | 10W | 20W | 35W |
| Load output current | 150-350mA | 100-550mA | 500-1050mA |
| Constant current/voltage Precision | Constant Current Precision ±5% |
| Wiring method | 0.5mm2 | Push terminal, wire cross section: 0.75-1.5mm2 |
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max.lead length:20M) |
| Dimming Range | Primary PUSH & DALI dimming: 0%-100% |
| DALI Dimming | DALI dimming (Max.lead length:300M) |
| Exception Protection Requirements | Output over temperature
protection | Yes, without self-recovery function(Can be inquired) |
| Output short circuit protection | Yes, without self-recovery function(Can be inquired) |
| Operating Environment | Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) |
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% |
| Max. case temp (Tc) | 85℃ |
| Safety & EMC | EMC standard | EN55015 EN61547 EN61000-3-2 EN61000-3-3 |
| DALI protocol standard | IEC62386-102, IEC62386-207 DT6 251 252 253 |
| Safety standard | EN61347-1 EN61347-2-13 |
| Certification | CE |
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) |
| Others | Degrees of protection | IP20 |
| Type of protection | Class II |
| Installation type | Independent installation & built-in installation |
| With crimping | / | 116*40.5*22mm | 136*42.5*24mm |
| Without crimping | 64.5*40*23mm | 78*40.5*22mm | 96*42.5*24mm |
| Blackout memory function | Yes, PUSH blackout memory |
| PUSH dimming synchronization | 15 units Max. |
| Packaging requirement | PE bag+Instruction+clapboard+outer carton(K=A) |
| Weight (With crimping) | / | 86.9±5g | 115.1±5g |
| Weight (Without crimping) | 54±5g | 100.5±5g | 132.7±5g |
| Life | 5 year @Ta full load |
| Note: All parameters are tested at the input voltage of 230VAC and a 25 °C environment unless specified. |
【Dimension】
【Wiring Diagram】
Fig. A DALI Dimming Fig.B Push Dimming
【Derating & Dimming Curve】
【Current Corresponding Voltage】
| KL35C-PDiiN |
| Current(mA) | Pomax(W) | Uout(V) |
| 500 | 20.0 | 3~ | 40 |
| 550 | 22.0 | 3~ | 40 |
| 600 | 24.0 | 3~ | 40 |
| 650 | 26.0 | 3~ | 40 |
| 700 | 28.0 | 3~ | 40 |
| 750 | 30.0 | 3~ | 40 |
| 800 | 32.0 | 3~ | 40 |
| 850 | 34.0 | 3~ | 40 |
| 900 | 35.1 | 3~ | 39 |
| 950 | 35.2 | 3~ | 37 |
| 1000 | 35.0 | 3~ | 35 |
| 1050 | 34.7 | 3~ | 33 |
The typical current data sets are for reference when selecting LED fixture models. More current levels can be set by NFC using a mobile APP adjustable in 1mA steps.
Scan the code to download Merrytek NFC
【ON/OFF & Description of Dimming Operation】
A. Short-press the PUSH switch (short press time 0.1s-1s), the LED driver will turn on or off.
B. Dimming: Press and hold the PUSH switch (1s-8s). The LED driver can achieve dimming, brightening, or both, with a dimming range of 1-100%.
C. Memory: PUSH dimming has dimming memory function.
D. Dimming synchronization: The power connected to the same PUSH switch can be synchronized by pressing and holding the PUSH switch for longer than 15s
E. DALI dimming mode: Connect the power supply to the DALI system, and it can be dimmed by the DALI host. The dimming range is 0-100%.
【 Matters Needing Attention】
1) The LED driver must be connected to the load before turning on the input power; otherwise, the LED driver may be damaged.
2) After the LED drive input is powered off, there will be a residual voltage at the output, which can be maintained for about 3 minutes.
3) Before setting the parameters via NFC, please ensure the driver is powered off.
Product Tags:
|
|
35W DALI2 & PUSH Dimming Constant Current LED Driver 500-1050mA With NFC Programmable Images
|
