| Series | Name | KL40VC-PDiiV |
| Input | Voltage range | 198~264Vac 50Hz /60Hz |
| Rated supply voltage | 220~240Vac 50Hz /60Hz |
| DC voltage range | 200~240Vdc |
| Input current | 0.21A Max.@230Vac |
| Inrush Current | 15A (Half current pulse width 100US) @230VAC |
| Power factor | ＞ 0.95 (@230Vac,100% load) |
| Total harmonic distortion | Typical: 16% (@230Vac, 100% load) |
| Stand-by power | ≤0.5W |
| Efficienc(@230Vac,100% load) | 87%Max |
| Wiring method | Push terminal, wire cross section:0.5-1.5mm2 |
| Loop-in&Loop-out quantity | 30PCS(@230Vac) |
| Automatic circuit breaker (Calculate current in the wire) | type | B10 | B13 | B16 | B20 | B25 | / |
| Number | 20 | 25 | 30 | 42 | 50 | / |
| type | C10 | C13 | C16 | C20 | C25 | C32 |
| Number | 25 | 40 | 50 | 70 | 80 | 100 |
| Output | Operating mode | Constant voltage |
| Load type | LED |
| Flickering / Flickering-Free | Flickering-Free |
| Start-up time | <1s (@230Vac) |
| Load output voltage range | 12V CV |
| Load output current | 3.33A Max. |
| Full load output power | 40W Max. |
| Minimum load | 3W |
| Output | Output current/voltage tolerance | ±5% |
| Wiring method | Push terminal, wire cross section:2*0.5-2.0mm2 |
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max. lead wire length:20m) |
| 1-10V(0-10V)Dimming | 0-10V dimming(Port current＜1mA),
(Max. lead wire length:20m) |
| Dimming Range | 0%-100% |
| Secondary PWM dimming | 0-10V port PWM dimming (3KHz-8KHz) |
| Potentiometer | Yes, 100kΩ |
| DALI function | DALI dimming (Max. lead wire length:300m) |
| Exception Protection Requirements | Output over temperature
protection | Yes, reset the power to recover |
| Output short circuit protection | Yes, reset the power to recover |
| Operating Environment | Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) |
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% |
| Max. case temp(Tc) | 85℃ |
Safety
& EMC | EMC standard | EN55015, EN61547, EN61000-3-2, EN61000-3-3 |
| DALI standard | IEC62386-101 / 102 / 207 DT6 / 209 DT8 |
| Safety standard | EN61347-1, EN61347-2-13 |
| Certification | CE |
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) |
| Others | IP Rating | IP20 |
| Type of protection | Class II |
| Installation type | Independent installation |
| Installation dimension | 150*52*28mm |
| Memory function | Yes, (PUSH with memory function) |
| PUSH dimming synchronization | Parallel: 15 units Max. Series: 25 units Max. |
| Packaging requirements | Instruction+clapboard+outer carton(K=A) |
| Weight | 300g |
| Life | 5 years @Ta 100% load |
| Note: All parameters are tested at an input voltage of 230VAC and a 25 °C environment, unless specified. |
